Super Cub Club - mcpx and dx6i settings?

« mcpx and dx6i settings? »

Welcome Guest. Please Login or Register.
May 20, 2013, 9:48pm

Super Cub Club :: News :: Off Topic :: mcpx and dx6i settings?

Author

Topic: mcpx and dx6i settings? (Read 1,101 times)

pauliepilot
Group captain

member is offline

didn't relise the ground was that high!!

Joined: Nov 2010
Gender: Male

Posts: 532
Location: united kingdom

mcpx and dx6i settings?
« Thread Started on Dec 16, 2011, 12:33pm »

Ok so i went out n bought a bnf mcpx hoverd around my front room...n thought i'll take it out to the field

my first fig 8s inpressed :-D and so happy...but not to sure about tro curves n stuff...tail dosnt hold sometimes n just spins?
And info or help would be great ;-) as i no one or two of us are heli flyers

Link to Post - Back to Top IP:

Logged

Brushless supercub,rtf supercub,phase 3 p-40 warhalk,flying wing,phase 3 squall x2,phase 3 ef16,parkzone extra300,blade450 3d,blade mcpx.....

freediverga
Flight lieutenant

member is offline

Joined: Dec 2011
Gender: Male

Posts: 78
Location: Dahlonega, Ga.

Re: mcpx and dx6i settings?
« Reply #1 on Dec 16, 2011, 6:39pm »

That's coaxial Helio right? You need adjust trim so both motors are spinning the same speed. My TX had a separate knob to do just that not sure about your dx6.

Link to Post - Back to Top IP:

Logged

Low 'n' Slow is the way its Done!!!

pauliepilot
Group captain

member is offline

didn't relise the ground was that high!!

Joined: Nov 2010
Gender: Male

Posts: 532
Location: united kingdom

Re: mcpx and dx6i settings?
« Reply #2 on Dec 18, 2011, 10:44am »

No its single bladed...flybarless!

Link to Post - Back to Top IP:

Logged

Brushless supercub,rtf supercub,phase 3 p-40 warhalk,flying wing,phase 3 squall x2,phase 3 ef16,parkzone extra300,blade450 3d,blade mcpx.....

pauliepilot
Group captain

member is offline

didn't relise the ground was that high!!

Joined: Nov 2010
Gender: Male

Posts: 532
Location: united kingdom

Re: mcpx and dx6i settings?
« Reply #3 on Dec 18, 2011, 10:50am »

My little mcpx

Link to Post - Back to Top IP:

Logged

Brushless supercub,rtf supercub,phase 3 p-40 warhalk,flying wing,phase 3 squall x2,phase 3 ef16,parkzone extra300,blade450 3d,blade mcpx.....

freediverga
Flight lieutenant

member is offline

Joined: Dec 2011
Gender: Male

Posts: 78
Location: Dahlonega, Ga.

Re: mcpx and dx6i settings?
« Reply #4 on Dec 18, 2011, 11:53pm »

should be some way to setup a trim dial on that DX6 doesn't have dial on the right and left side? The tail rotor is either spinning to fast or to slow. You have to have it adjusted just right because it has to speed up and slow as you you increase the boost because it has to counter act the the increased torque of the main rotor. You have to be able to hookup the TX to your computer and assign one of the dials to do the trim. once you figure that out get the helio off teh ground 16-18 inches off the ground then adjust with the dial. At that height ground affect shouldn't affect the helio so you can get the trim setup

Link to Post - Back to Top IP:

Logged

Low 'n' Slow is the way its Done!!!

freediverga
Flight lieutenant

member is offline

Joined: Dec 2011
Gender: Male

Posts: 78
Location: Dahlonega, Ga.

Re: mcpx and dx6i settings?
« Reply #5 on Dec 18, 2011, 11:56pm »

http://www.rcuniverse.com/forum/m_10450757/printable.htm

try this out

Link to Post - Back to Top IP:

Logged

Low 'n' Slow is the way its Done!!!

pauliepilot
Group captain

member is offline

didn't relise the ground was that high!!

Joined: Nov 2010
Gender: Male

Posts: 532
Location: united kingdom

Re: mcpx and dx6i settings?
« Reply #6 on Dec 24, 2011, 1:23pm »

Thanks for ur help...iv found settings that calm the mcpx down n make it fly a little more like my blade450

Im on my way now doing fig8s with the mcpx..bought a few bits for it allready but least a crash with the mcpx costs £10 normaly its just links that pop off

£40+ with the blade450 :-0

« Last Edit: Dec 24, 2011, 1:26pm by pauliepilot »

Link to Post - Back to Top IP:

Logged

Brushless supercub,rtf supercub,phase 3 p-40 warhalk,flying wing,phase 3 squall x2,phase 3 ef16,parkzone extra300,blade450 3d,blade mcpx.....

pauliepilot
Group captain

member is offline

didn't relise the ground was that high!!

Joined: Nov 2010
Gender: Male

Posts: 532
Location: united kingdom

Re: mcpx and dx6i settings?
« Reply #7 on May 4, 2012, 4:48pm »

Update:
So i pulled the servo port off the main board of my poor mcpx :-(

So i sold it cheep n going to put the money towards a blade 130x......the mcpx has made a big diffrence in my flying

Only last week i looped n rolled my blade 450 :-D cant wait for the 130x to be shiped

)

Link to Post - Back to Top IP:

Logged

Brushless supercub,rtf supercub,phase 3 p-40 warhalk,flying wing,phase 3 squall x2,phase 3 ef16,parkzone extra300,blade450 3d,blade mcpx.....

Click Here To Make This Board Ad-Free